Thanks Thanks:  1
Likes Likes:  1
Results 1 to 3 of 3

Thread: Quadzilla Adrenaline with Pulse Programming Custom Tunes

  1. Top Of Page | #1
    Old & Grumpy! Polaraco's Avatar

    User Info Menu

    Quadzilla Adrenaline with Pulse Programming Custom Tunes

    Quadzilla Adrenaline with Pulse101

    Parameters Monitored: withadditional User Defined Warnings on all parameters:
    EGT
    Boost
    Transmission Temp
    Coolant Temp
    Fuel Pressure
    RPM
    MPH
    Corrected MPH
    ECM Voltage
    Back-down %
    TPS%
    IAT
    Fuel Temperature
    Power Level
    Oil Pressure*
    Engine Load%

    User Defined De-fuel Settings:
    EGT
    Boost
    Transmission Temp
    Coolant
    Fuel Pressure

    User Controlled Features:
    Turbo Timer (select time or EGTbased, control desired run-time or EGT for shut-off)
    Warm Up (select coolanttemperature at which the Adrenaline starts adding power)
    High Idle Delay (select amountof time before high idle activates in an idle state)


    Min/Max Recording Log for:
    EGT
    Boost
    Transmission Temp
    Coolant Temp
    Fuel Pressure
    RPM
    MPH
    Corrected MPH
    ECM Voltage
    Back-down %
    TPS%
    IAT
    Fuel Temperature
    Power Level
    Oil Pressure*
    Engine Load %


    Adjustments:
    tuning options including:
    Timing Advance
    Can Bus Fueling
    Pump Stretch Fueling
    Throttle Response options.

    Pump Stretch.

    This will make the biggestdifference in overall power and smoke. This is the amount of time the injectoris actually opened and spraying fuel into the cylinder. I have this set prettylow on the 1000 tune that I sent you. The COMP file is set to 1800. More than1800 creates more torque and a lot more smoke but, actually makes less power onthe upper end based on all the trucks I have had on the dyno. This is where theCOMP file is set to. Feel free to run it to 2400 anytime you want lots of lowend power and smoke but, realize you are giving power up on the top.

    This does not mean you will getthis amount of fuel all the time. There is a map, in percentages based off ofthis number as the maximum. Beyond that the map is also scaled by the TPS. Soeven if the map commands 100% but, you are at 50% throttle you will be getting50% of the max stretch. If the map calls for 25% and you are at 50% TPS youwill be getting 12.5% of the max stretch.


    TPS MIN. For both CAN and Pumpfueling.

    This allows you to make thethrottle lighter or more responsive. Basically it gives you a fudge factor thatallows you to get a minimum amount of the max fuel stretch all the time. If youset this to 10% you will never get less than 10% of the fuel map. So if the mapcalls for 100% (1800) but, you are at 5% throttle you would normally get 5% ofthe map. If you set this parameter to 10% you will get 10% even though themapping algorithm calls for 5%.

    You have to be somewhat carefulwith this or you will be fueling way too much at light throttle. This is set to0% on the tune I sent out.


    TPS MAX. Both CAN and PumpStretch.

    This allows you to determinewhat throttle position you will see max fueling at. It also re-scales theentire map based on what you select. This is set to 100% on tunes I sent out.This means that you will not get 100% of the map unless you are at 100% TPS. Ifyou set this at 80% TPS that means you will get 100% of the fueling at 80% TPS.It also means that 80%=100% and the map is scaled between 0% and 80% but, on a0-100 scale. In other words the map moves in increments of .8% instead of 1%.

    This can be really useful forthose that drive light but, want power on tap earlier in the pedal but, notnecessarily right off idle.


    Timing MAX

    Sort of goes without saying. 0means we do not add any timing. 10deg means if the map calls for 100% you willget 10deg added over stock.

    I never go over 7.5%. In myopinion that is more than plenty. If you are going for only mileage and aregoing to be easy you can use 10 deg and it should be great for mileage. Theproblem is that under much boost it could easily cause headgasket damage.


    Boost Scaling.

    This function is more of asmoothing function of the map. There are 20 positions that this functioncontrols. Think of it at columns. Until boost equals a certain amount, then itis in a certain column. It takes more or less boost to move to differentcolumns.

    So if you set this to 20, theneach column is changed by 1psi. If you scale it to 40psi then every 2psi itchanges.

    While this can make things moreor less responsive or smooth it out slightly it does not make huge differencesbecause not necessarily every column is more or less aggressive than the next.There have been maps in the past and there will be maps in the future wherethey will be more boost reliant. For now we do not rely on boost that muchother than as this scaling function.
    -Thanks To RacerRon

    --------------------------------
    TIPS:

    Things that will make moresmoke:
    Lowering the Boost scale down
    Lowering TPS MIN on both CAN andfor the PUMP
    Lowering TPS MAX on both CAN andPUMP
    Raising MAX PUMP STRETCH
    Lowering MAX TIMING
    Lowering TIMING SCALE

    All those things in one way oranother will make more smoke. Raising the pump stretch is the simplest way todo it.

    Stacking With a Timing Module:
    You can set the MAX timingadvance to 0 or you can set the timing scaling to 0%.
    Either way you get 0 timing.

    lower the scaling, the softerthe curve:
    If you turn the MAX up, and thecurve down, you will get more timing down low then the factory settings withthe MAX timing ending up about the same.
    If you turn the max up to 10degMAP. and then scale it by 80% you will end up with 2.4 deg advance in that sameexact map spot and a MAX of 8deg at WOT.
    100% scaling gives you the mostaggressive map for a given MAX timing value.

    ----------------------------------
    Custom Tune Reports:

    Dyno
    Fuel Stretch 2200
    Timing 10*
    Pump max 100
    Pump min 0
    Can max 100
    can min 0
    Boost scaling 20

    COMP2 - Default
    power levels 4
    max pump stretch 1200
    Tps can max/min 100/30
    boost scale 38
    and everything else set to 0.

    COMP Tune - SuggestedAdjustments
    Fuel stretch 2200
    Timing 10*
    Pump max 100
    Pump min 0
    Can max 100
    Can min 0

    COMP Tune - SuggestedAdjustments
    Timing = 7
    Fuel Stretch = 1800
    TPS MIN = 0 (both can and pump)
    TPS MAX CAN = 100
    TPS MAX Pump = 70
    Boost Scaling = 25

    Surge free, killer bottomend,totally sick mid powerband! Strongest tune ever!!!!
    set fuel stretch to 2200,
    timing to 10*,
    can min to 30, max to 100%,
    pump min to 30, max to 100%,
    boost scale to 25.



    2003- 3500 RWD Automatic.
    S & B intake, BD Intercooler, Pusher Air Horn, MM3 Double R Tuning, Turbo Timer, electric Flex-a-lite fans, FASS 95,
    50 HP tips, upgrade to 351 turbo, 3.42 gears, Twin air compressors, air bags, Remote dual oil filters, Hellwig sway bar, Front Winch. Home made Fuel Heater, BD Exhaust brake with Torque Lock. Tons of TLC

  2. Thanks LukeCamp84 thanked for this post
    Likes kirkcalloway liked this post
  3. Top Of Page | #2
    Basic Member

    User Info Menu

    Great info. I will look at my current settings and add them if different than what you posted.


  4. Top Of Page | #3
    Basic Member

    User Info Menu

    Is this thread for the 3rd gen cummins I have an 06 5.9 does this information work for this make/year ?? Thanks


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •