Alarm,remote start

[dmuney]

Here is some info that may help some of you, its not all there but ill be updating when I can, its a lot of info that i need to double check before I post it.

There will be more coming including relay wiring diagrams, its just going to take awhile to get everything confirmed and posted due to the fact I'm rebuilding my motor at this moment. here you go
14 ram.txt08 ram.txt07 RAM.txt06 RAM.txt05 RAM.txt

Any requests for more ill try to get them in the order they get asked for if possible

this sucks the links are not working ill try to get it figured out

 0 Comment(s)

[dmuney]

Ok here it is not all posts contain every piece of information but some do. I'll start with newer trucks first. relay diagrams will come later.

 0 Comment(s)

[dmuney]

2012 ram connections and locations


12volts red (40A) + BCM under driver dash, black 4 pin plug (B), pin 3
Starter lt. blue/tan + BCM under driver dash, black 24 pin plug (A), pin 19
Second Starter purple/brown Ignition Node/Keyless Ignition Node Module, blk 6 pin plg, pin 4
Ignition pink/white + BCM under driver dash, black 48 pin plug (E), pin 27
Second Ignition brown + BCM under driver dash, black 24 pin plug (A), pin 18
Third Ignition N/A
Accessory brown/orange + BCM under driver dash, black 48 pin plug (E), pin 36
Second Accessory N/A
Keysense N/A
Power Lock purple/lt. green (passenger door switch) - 330 ohms Passenger Door Module, black 10 pin plug, pin 4
Power Unlock (same as power lock) - 100 ohms
Lock Motor lt. green/dk. blue 5 wire BCM under driver dash, white 48 pin plug (F), pin 2
Unlock Motor tan/lt. green 5 wire BCM under driver dash, white 48 pin plug (F), pin 1
Parking Lights+ white/brown (LF); white/orange (RF) + BCM, black 24 pin plug (A), pin 4; white 24 pin plug (D), pin 3
Notes: The LR - RR are white/gray - white/orange (+) at the BCM under driver dash, white 48 pin plug (F), pin 32; black 48 pin plug (E), pin 4.
Parking Lights- white/brown (need to relay isolate the switch) -1130 ohms BCM under driver dash, blue 24 pin plug (G), pin 20
Hazards white/dk. blue - BCM under driver dash, blue 24 pin plug (G), pin 21
Turn Signal(L) white/lt. green (F); white (R) + BCM, white 24 pin plug (D), pin 14; white 48 pin plug (F), pin 40
Turn Signal(R) white/tan (F); white/lt. green (R) + BCM, black 24 pin plug (A), pin 13; black 48 pin plug (E), pin 2
Reverse Light white/tan + BCM under driver dash, white 48 pin plug (F), pin 41
Door Trigger purple - BCM under driver dash, white 48 pin plug (F), pin 9
Dome Supervision yellow/purple + BCM under driver dash, blue 24 pin plug (G), pin 14
Trunk/Hatch Pin N/A
Hood Pin purple/lt. blue - BCM under driver dash, black 24 pin plug (A), pin 11
Trunk/Hatch Release N/A
Power Sliding Door N/A
Factory Alarm Arm (arms on lock with door open)
Factory Alarm Disarm (see disarm no unlock)
Disarm No Unlock (transponder and ignition)
Tachometer On diesel models, use dk. blue/gray at the camshaft position sensor, 3 pin plug, pin 3.
Wait to start N/A
Brake Wire dk. green/white + BCM under driver dash, white 24 pin plug (D), pin 18
Parking Brake dk. green/white - BCM under driver dash, black 48 pin plug (E), pin 11
Horn Trigger dk. green/white + BCM under driver dash, black 24 pin plug (A), pin 23

 0 Comment(s)

[dmuney]

2008 ram connections and locations



Battery LIGHT BLUE/RED (+) IGNITION SWITCH HARNESS
Ignition 1 PINK/WHITE (+) IGNITION SWITCH HARNESS
Ignition 2 PINK/GREEN (+) IGNITION SWITCH HARNESS...NOT ON ALL MODELS, BUT IF PRESENT MUST BE ENERGIZED TO AVOID CHECK ENGINE LIGHT
Accessory 1 VIOLET/BROWN (-) IGNITION SWITCH HARNESS
Starter 1 YELLOWGRAY (+) AT MODULE UNDER HOOD...NOT FOR REMOTE START, USE STARTER2,
Starter 2 VIOLET/BROWN (-) IGNITION SWITCH HARNESS...If the starter bumps on a key-takeover when remote started, you must interrupt the Violet/Brown MUX wire from the ignition cylinder and wire a relay


Anti-Theft Type DAIMLER SENTRY KEY® VEHICLE IMMOBILIZER
Anti-Theft Descript THE KEY SENDS AN RF SIGNAL TO THE BCM MODULE THROUGH AN ANTENNA LOCATED AROUND THE IGNITION CYLINDER
Note if you take a key already programed to vehicle and securly attatch it as near as possible to ignition switch the BCM will recieve its RF signal, usualy requires removal of steering column cover


Key Sense VIOLET/BROWN (-) IGNITION SWITCH HARNESS
Tachometer DARK BLUE/GRAY (AC) AT PCM MODULE ON PASSENGER SIDE FIREWALL
Speed Sense DARK GREEN/BROWN (AC) AT PCM MODULE ON PASSENGER SIDE FIREWALL
Parking Lights WHITE/LIGHT GREEN (-) AT VEHICLE LIGHT SWITCH...MUST ISOLATE FROM THE SWITCH WITH A RELAY DUE TO A REST RESISTANCE FORM THE SWITCH, USE A 1.1K OHM RESISTOR posted_image
Brake Lights WHITE/TAN (+) AT SWITCH ABOVE BRAKE PEDAL
Reverse Lights WHITE/LIGHT GREEN (+) IN HARNESS UNDER HOOD ON DRIVER FENDER
Horn DARK GREEN/VIOLET (-) IN HARNESS AT STEERING COLUMN
Databus WHITE/ORANGE (DATA) IN HARNESS AT STEERING COLUMN
Door Lock Circuit LIGHT GREEN/ORANGE (-) IN HARNESS IN DRIVER KICKPANEL...USE A 2K OHM RESISTOR FOR LOCK, 480 OHM RESISTOR FOR UNLOCK,
Power Unlock VIOLET/DARK GREEN (-) IN HARNESS IN DRIVERS KICKPANEL...USE 330 OHM RESISTOR FOR UNLOCK
PowerLock VIOLET/DARK GREEN (-) IN HARNESS IN DRIVERS KICKPANEL...USE 820 OHM RESISTOR FOR LOCK
LF Window Up ORANGE/LIGHT GREEN (REV) AT DRIVER WINDOW SWITCH
LF Window Dn ORANGE/WHITE (REV) AT DRIVER WINDOW SWITCH
Window Up ORANGE/TAN (REV) IN HARNESS IN DRIVER KICKPANEL TO DOOR
RF Window Dn ORANGE/GRAY (REV

 0 Comment(s)

[dmuney]

2007 ram



12volts lt. blue/red (2A) + ignition harness
Starter yel/gry (not for remote start) + near battery, gray plug
Notes: There is no positive starter wire required for remote start. Just use the negative second starter wire.


Second Starter purple/brown - ignition harness
Notes: The second starter wire is negative trigger thru an 180 ohm resistor. MUST use a relay. Refer to DirectFax document 1084 for wiring information.


Ignition pink/white + ignition harness
Second Ignition N/A
Third Ignition N/A
Accessory same as second starter wire
Notes: The accessory wire is negative trigger thru a 610 ohm resistor. MUST use a relay. Refer to DirectFax document 1084 for wiring information.


Second Accessory N/A
Keysense N/A
Power Lock purple/dk. green - DKP or cluster, sml gry plug, pin 3
Notes: Lock is negative trigger thru an 820 ohm resistor. Unlock is negative trigger thru a 330 ohm resistor. MUST use relays.
Can also use Directed interface module.


Power Unlock same as power lock wire
Lock Motor lt. green 5wi DKP or cluster, white plug, pin 10
Unlock Motor tan/lt. green 5wi DKP or cluster, white plug, pin 1
Parking Lights+ white/yel (L), white/gray (R) + harness at top of driver fender
Parking Lights- white/lt. green - sw or cluster, sml gry plug, pin 5
Notes: Parking lights are negative trigger thru a 1130 ohm resistor. MUST use a relay.


Hazards white/orange - sw or cluster, sml gry plug, pin 8
Notes: Hazards are negative trigger thru a 120 ohm resistor. MUST use a relay.
Turn Signal(L) wht/lt grn (F), wht/dk grn (R) + harness at top of driver fender
Turn Signal(R) white/tan (F), white/yel (R) + harness at top of driver fender


Reverse Light white/lt. green + harness at top of driver fender
Door Trigger see notes - each kick or cluster, lrg gray plug
Notes: The LF door is purple in pin 1. The RF door is purple/white in pin 4. The LR door is purple/orange or purple/gray in pin 2. The RR door is purple/yellow or tan/yellow in pin 3. Use all four wires and diode isolate each wire from each other and the instrument cluster. See DirectFax document 1076 for wiring information.


Dome SupervisioN yellow/lt. blue + A pillar or cluster, wht plg, pin 21
Trunk/Hatch Pin N/A
Hood Pin purple/lt. blue - hood pin switch
Trunk/Hatch Release N/A
Power Sliding Door N/A
Factory Alarm Arm arms on lock with door open
Factory Alarm Disarm factory remote only
Disarm No Unlock with ignition and Sentry Key
Tachometer On diesel models, the tach wire is at the ECM on the lower driver side of the engine, front 60 pin plug, pin 24, or at the camshaft position sensor just left of the ECM, in a 3 pin plug.


Wait to start see DirectFax document 1091
Notes: On the remote start module, make sure to program the Accessory State During Wait To Start to ON.


Brake Wire white/tan + brake pedal switch
Parking Brake dk. green/white - sw or cluster, lrg gry plug, pin 22
Horn Trigger dk. green/purple - sw or cluster, lrg gry plug, pin 14

Interface Module: Category: Combo Interface Required: NO Type: Data Bus Part #: IOM-Chrysler-7
Notes: When using the IOM-Chrysler-7 the module will control the locks, trunk, door trigger, and bypass but it is still necessary to use doc 1084 for 2nd accessory and starter. Do not hook up the pink/white multiplex output from the IOM-Chrysler-7 to the purple/brown in the vehicle. Use doc 1084 instead.


Interface Module: Category: Immobilizer Bypass Required: Yes Type: Sentry Key Part #: 556CW
Alternate Part1 #: 556UW
Alternate Part2 #: DesignTech 20402
Alternate Part3 #: DesignTech 29402
Notes: Standard on all models.
Interface Module: Category: Door Lock Interface Required: No Type: Multiplex

 0 Comment(s)

[dmuney]

2006 ram





12volts lt. blue/red (2A) + ignition harness
Starter dk. green/yellow + ign harn or starter button (SRT-10)
Second Starter purple/brown - ignition harness
Notes: The second starter wire is negative trigger thru an 180 ohm resistor. MUST use a relay. Refer to DirectFax document 1084 for wiring information.


Ignition pink/white + ignition harness
Second Ignition N/A
Third Ignition N/A
Accessory same as second starter wire - ignition harness
Notes: The accessory wire is negative trigger thru a 610 ohm resistor. MUST use a relay. Refer to DirectFax document 1084 for wiring information.


Second Accessory N/A
Keysense N/A
Power Lock purple/dk. green - DKP or cluster, sml gry plug, pin 3
Notes: Lock is negative trigger thru an 820 ohm resistor. Unlock is negative trigger thru a 330 ohm resistor. MUST use relays.
Can also use a interface module.
Power Unlock same as power lock wire


Lock Motor lt. green 5wi DKP or cluster, white plug, pin 10
Unlock Motor tan/lt. green 5wi DKP or cluster, white plug, pin 1
Parking Lights+ white/yel (L), white/gray (R) + harness at top of driver fender
Parking Lights- white/lt. green - sw or cluster, sml gry plug, pin 5
Notes: Parking lights are negative trigger thru a 1130 ohm resistor. MUST use a relay.


Hazards white/orange - sw or cluster, sml gry plug, pin 8
Notes: Hazards are negative trigger thru a 120 ohm resistor. MUST use a relay.


Turn Signal(L) wht/lt grn (F), wht/dk grn (R) + harness at top of driver fender
Turn Signal(R) white/tan (F), white/yel (R) + harness at top of driver fender
Reverse Light white/lt. green + harness at top of driver fender
Door Trigger see notes - each kick or cluster, lrg gray plug
Notes: The LF door is purple in pin 1. The RF door is purple/white in pin 4. The LR door is purple/orange or purple/gray in pin 2. The RR door is purple/yellow or tan/yellow in pin 3. Use all four wires and diode isolate each wire from each other and the instrument cluster. See DirectFax document 1076 for wiring information.


Dome Supervision yellow/lt. blue + A pillar or cluster, wht plg, pin 21
Trunk/Hatch Pin N/A
Hood Pin N/A
Trunk/Hatch Release N/A
Power Sliding Door N/A
Factory Alarm Arm factory remote only
Factory Alarm Disarm factory remote only
Disarm No Unlock with ignition and Sentry Key
Tachometer On diesel models, the tach wire is at the ECM on the lower driver side of the engine, front 60 pin plug, pin 24, or at the camshaft position sensor just left of the ECM, in a 3 pin plug.
Brake Wire white/tan + brake pedal switch
Parking Brake dk. green/white - sw or cluster, lrg gry plug, pin 22
Horn Trigger dk. green/purple - sw or cluster, lrg gry plug, pin 14

 0 Comment(s)

[dmuney]

2005 ram and probably the most complete



12volts red (40A), red (40A) + ignition harness
Starter yellow + ignition harness
Second Starter N/A
Ignition pink/white + ignition harness
Second Ignition pink/lt. green + ignition harness


Third Ignition pink/yellow (10 AWG)(3rd acc) + ignition harness
Notes: This wire is not required for remote start. It only provides power to the power window circuit.


Accessory dk. blue and pink/yel (16 AWG) + ignition harness
Second Accessory pink/yellow (14 AWG) + ignition harness
Keysense purple/tan - ignition harness


Power Lock purple/dk. green - driver kick, door harness
Notes: Lock is negative trigger thru an 820 ohm resistor. Unlock is negative trigger thru a 330 ohm resistor. MUST use relays.
Can also use Directed 457C or 456L interface modules.
Power Unlock same as power lock wire


Lock Motor lt. green 5wi driver kick, door harness
Unlock Motor tan/lt. green 5wi driver kick, door harness
Parking Lights+ white/yel (L), white/gray (R) + harness at top of driver fender
Parking Lights- white/lt. green - headlight switch
Notes: Parking lights are negative trigger thru a 590 ohm resistor. MUST use a relay

Hazards white/orange - hazard switch
Notes: Hazards are negative trigger thru a 120 ohm resistor. MUST use a relay.
Turn Signal(L) use hazards wire
Turn Signal(R) use hazards wire


Reverse Light white/lt. green + at tail light


Door Trigger see notes - see notes
Notes: The driver door trigger is purple and the driver side rear door is purple/orange. These wires are in the driver kick panel. The passenger door trigger is purple/white and the passenger side rear door is purple/yellow. These wires are in the passenger kick panel. Use all four wires and diode isolate each. See DirectFax document 1076 for wiring information.


Dome Supervision yellow/lt. blue or yellow/org + driver A pillar or cluster
Trunk/Hatch Pin N/A
Hood Pin N/A
Trunk/Hatch Release N/A
Power Sliding Door N/A


Factory Alarm Arm purple/lt. blue - driver kick, door harness
Notes: This will also do door locks. Arm/lock is negative trigger thru a 644 ohm resistor. Disarm/unlock is negative trigger thru a 1565 ohm resistor. Single pulse will do disarm without unlocking the doors. Unlock requires a double pulse. MUST use relays.
Can also use Directed 457C or 456L interface modules.
Factory Alarm Disarm same as factory alarm arm wire
Disarm No Unlock see factory alarm disarm

Tach Signal On diesel models, the tach wire is at the ECM on the lower driver side of the engine, 60 pin plug, pin 24, or at the camshaft position sensor just left of the ECM, in a 3 pin plug.
Brake Wire white/tan + brake pedal switch
Parking Brake dk. green/white - parking brake switch
Horn Trigger dk. green/purple - horn switch
Memory Seat 1 N/A
Memory Seat 2 N/A
Memory Seat 3 N/A


Immobilizer Bypass Module: Required: Yes Type: Sentry Key Part #: 555C, 556U, or 555U
Notes: Only vehicles with gray keys have the immobilizer.






Audio





Radio 12v gray/red + radio harness
Radio Ground black and black/lt. green - radio harness
Radio Ignition pink/yellow + radio harness
Radio Illumination orange/tan (dimmer) + radio harness
Factory Amp Turn-on N/A
Power Antenna N/A
LF Speaker +/- dk. grn/yel - dk. grn/lt. blue +,- radio harness or amplifier
Notes: The amplifier is behind the glove box.


RF Speaker +/- gray/yellow - gray/lt. blue +,- radio harness or amplifier
LR Speaker +/- gray/lt. grn - gray/dk. grn +,- radio harness or amplifier
RR Speaker +/- dk. grn/lt. grn - dk. grn/gray +,- radio harness or amplifier


Immobilizer Bypass Module: Required: Yes Type: Sentry Key Part #: 555C, 556U, or 555U
Notes: Only vehicles with gray keys have the immobilizer.




Accessory









12volts red (40A), red (40A) + ignition harness
Ignition pink/white + ignition harness


Parking Lights+ white/yel (L), white/gray (R) + harness at top of driver fender
Parking Lights- white/lt. green - headlight switch
Notes: Parking lights are negative trigger thru a 590 ohm resistor. MUST use a relay.


Headlight white/lt. green - headlight switch
Notes: Headlights and parking lights are negative trigger thru a 1100 ohm resistor. MUST use a relay.


Trunk/Hatch Release N/A
Power Sliding Door N/A
Speed Sense On diesel models, the vss wire is at the ECM on the lower driver side of the engine, 50 pin plug, pin 11.
Wipers brown/wht (L), brown/org (H) + windshield wiper motor
LF Window up/dn orange/lt. green - orange/wht A driver window switch in door
RF Window up/dn orange/tan - orange/gray A driver kick, door harness
LR Window up/dn orange/white - orange/gray A driver kick, door harness
RR Window up/dn orange/lt. blu -orange/dk. blu A driver kick, door harness

 0 Comment(s)

[dmuney]

Ok so here is the relay info and honestly way to much info for me to rewrite so I’m sharing direct links to all the relay diagrams. Enjoy

 0 Comment(s)