Thanks Thanks:  13
Likes Likes:  18
Results 1 to 4 of 4

Thread: Randy’s 68RFE build parts

  1. Top Of Page | #1
    Rdchan98's Avatar

    User Info Menu

    Randy’s 68RFE build parts

    I’m looking to buy a Randy’s transmission’s stage 2 68RFE DIY or plug-and-play kit; who’s the best and cheapest place to buy from?

    Are any Randy’s dealers on here, or should they go straight through them?

    Does anyone have reviews on these kits?

    I have 2 Dodge dealer techs who offered to help me build either setup, one being my uncle, so I should have access to all the special tools required.

    Are there other build kits I should look into that’ll handle 650+hp?

    All advice is appreciated; thanks.

    2013 2500 tradesman ccsb leveled 35’s 20x10 Tis 544’s 167k miles Raceme ultra, gutted factory intake, stainless intake ram, grid heater delete, exotic head studs, ddp 90hp injectors, II CP3, bmp 150gph lift pump,stock air, 5” turbo back with 8” tip, custom rear bumper, trifold bed cover, bd separator plate and sonnex shift kit in trans

  2. Thanks AK Bob, inline6c, IGOTACUMMINS thanked for this post
  3. Top Of Page | #2
    I WILL STAND! AK Bob's Avatar

    User Info Menu

    Re: Randy’s 68RFE build parts

    @DDP I know you offer Randy’s built transmissions.

    Do you have any advice on where to purchase the DIY kit?

    2014 RAM 3500 (Aisin) 3.73 4X4 Limited Crew Cab Long Bed DRW. Oil Bypass Filter, Fuel Filtration Kit, Cold Air Intake, City Diesel Actuator and 50 Gallon Aux Fuel Tank.

  4. Top Of Page | #3
    #1 VENDOR cumminsdieselfreak's Avatar

    User Info Menu

    Re: Randy’s 68RFE build parts

    Quote Originally Posted by Rdchan98 View Post
    I’m looking to buy a Randy’s transmission’s stage 2 68RFE DIY or plug-and-play kit; who’s the best and cheapest place to buy from?

    Are any Randy’s dealers on here, or should they go straight through them?

    Does anyone have reviews on these kits?

    I have 2 Dodge dealer techs who offered to help me build either setup, one being my uncle, so I should have access to all the special tools required.

    Are there other build kits I should look into that’ll handle 650+hp?

    All advice is appreciated; thanks.
    We're a dealer, but Randy's doesn't give dealers full catalog access, only select items.

    The DIY kit from RevMax doesn't support that much HP.

    I'd recommend going directly to Randy's.

    Tell them DDP Motorsports referred you directly to them.

    2018 Ram 2500 4x4 G56
    Romans 10:13

    See what we are up to on:
    FACEBOOK | INSTAGRAM
    Or Email me at:
    joe@ddpmotorsports.com
    www.ddpmotorsports.com


  5. Top Of Page | #4
    TWN495's Avatar

    User Info Menu

    Re: Randy’s 68RFE build parts

    It's a somewhat related question.

    I was looking at Randy's website, and he includes tuning specs that his trannys call for.

    Does anyone know if the standard DRD trans tuning that folks may have on their trucks would suffice?

    It Calls For:

    • LINE PRESSURE SET TO 225PSI ABOVE 30% THROTTLE ANGLE
    • 100PSI RESTING PRESSURE
    • NO LOCKUP UNTIL 4TH GEAR
    • LOW/REVERSE SPRAG HOLDOUT
    • FOR 2019+, UNDERDRIVE PULSE TEST MUST BE TURNED OFF.


    2016 Ram 2500 Laramie, CC SB, Thuren leveling kit, Toyo AT3 37/12.5x18s, Method NV HDs, 4.10 AAM gears, Airlift bags/compressor

  6. Thanks watersupply189, IGOTACUMMINS thanked for this post
    Likes Corkey, watersupply189, IGOTACUMMINS liked this post

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •