Perfect, I just needed to know for sure to quit overthinking!
Thank you for answering all my questions and giving me all the insight!
Sent from my iPhone using Tapatalk
Perfect, I just needed to know for sure to quit overthinking!
Thank you for answering all my questions and giving me all the insight!
Sent from my iPhone using Tapatalk
I remember seeing this post about a week ago, so I finally decided to purchase a Pusher mega 3.5-inch tube for the driver's side, aka cold side.
I wanted to do the hot side by the turbo, but as Corkey said, it probably won't fit my 2nd Gen S467.7 setup.
So on that side, I still have Smedings metal pipe hooked up to my Stainless Diesel turbo.
Don't forget to put the rubber o-ring on the end of that pipe that v-bands to the turbo if you have Smedings.
I double-checked mine the other day, and well not there, LOL.
It was probably sealed up, but I think it may have had a slight boost leak where they joined together.
A trip to Oreillys and a universal o-ring fixed that.
Anyway, I hope to see good results with the dented-looking restrictive oem pipe out of the way.
This will be hooked up to GDP Intake Horn, GDP gride heater delete plate and grid heater.
If it helps any other member, my truck is on stock fuel Steed Speed manifold, Stainless S467.7 5 blade, and I sometimes tow heavy.
Also, if any members know what parts are needed to replace the hot side pipe, let me know because oil changes suck.
My turbo is low mounted, and I have looked at a v-band 90-degree elbow that comes off the turbo and maybe a strait pipe to a curved boot.
Something that would be possibly easier to take apart when getting to the oil filter.
I never really cared for Smeding's hot side pipe because it is difficult to line up for the initial installation.
So I got the Pusher Mega 3.5 drivers side boost tube in.
The quality is top-notch with everything I received, so I am thrilled.
The installation, though, was a little rough, I won't lie.
Trying not to scratch up the powder coating on the pipe is next to impossible, and the clamps for the intercooler end are tough to reach due to the power steering gearbox being in the way.
I had to use a ratcheting wrench, which was difficult even then.
I got it lined up and finally got the boot over my GDP grid heater.
When I took the truck for a drive, I will say that I think the EGTs were a tad cooler and that it helped with some mid-range spool of the turbo and even with the intake temperature.
So, in the end,d after hating the installation, I think it was worth it.
Pushers' quality is top-notch, and I think regardless of who you use, it's not going to be easy getting a 3.5-inch pipe in there, and it's the nature of the beast.
Look at the difference in size versus stock.
Honestly, your best bet is just getting into contact with a fab shop and getting something made or changing to a high-mount kit.
I don't think you're going to find much otherwise.
V-band (both ends) ninety off the turbo, and then a short stub of pipe with a v-band connection on one side stuffed into the intercooler boot, charge pipe in between.
Yeah, I guess I would have to flip my Steed Speed manifold, also.
I mean, I guess by the time I am done, it would cost a good chunk of money.
I may leave it at this point and have fun pulling the fender liner every time I do an oil change.
I do have the screw-on T-tool for the oil filter, so at least it won't spill everywhere fishing it out.
I guess it's one of those things that if I had a choice to do it over, I would've gone high mount and not Smeding, to begin with.[
Yes, you would have to flip it and possibly add a spacer.
New downpipe, intake, and oil lines.
Sent from my iPhone using Tapatalk
Bookmarks