Are any sponsors here selling the cat front fuel filter adapter kits?
Looking to purchase one and thought I'd check here first.
Are any sponsors here selling the cat front fuel filter adapter kits?
Looking to purchase one and thought I'd check here first.
I am the upper end of lower class.
@DDP
Do you guys carry these?
71Silverbullet
If funds are not a big issue.
I highly recommend a FASS system.
I don't have any experience with Cat filters personally.
II 60HP STICKS, II 33% CP3, II S464 2ND GEN SWAP, FASS 165 TITANIUM SIGNATURE SERIES, AFE INTAKE HORN, S&B FILTER, 5" TURBO BACK, ALPHAREX HEAD LIGHTS, 38X13.5X20 RAZOR M/T, MOTO METAL RIMS, 6" LA LIFT KIT, COMPLET MM3 KIT, BUILT TRANSMISSION, 6 BOLT REDHEAD STEERING BOX, YUKON 4.56 GEARS W/ COVERS
I don't have any mods that require the higher pressure pump.
The cat system uses a readily available 2-micron spin-on filter and is a 2-beer install compared to an all-day install on the FASS.
Then there is the $600 price difference.
Nothing against the FASS or any other lift system; I think they would be overkill for my needs. (I may be wrong about this?)
I'm looking for better filtration and the stock plastic filter housing elimination.
Thanks for the suggestion.
I am the upper end of lower class.
If you decide to install the kit from “Diesel Fuel Filter Kits,” you may want to consider replacing the filter head with this kit.
See the link below.
https://www.igotacummins.com/threads...And-Oil/page10
2014 RAM 3500 (Aisin) 3.73 4X4 Limited Crew Cab Long Bed DRW. Oil Bypass Filter, Fuel Filtration Kit, Cold Air Intake, City Diesel Actuator and 50 Gallon Aux Fuel Tank.
I did purchase the 2 beer version, and I don't have the factory rear filter, just the canister one on the block, which is where my water-in-fuel sensor is located.
OK, I have not added my cat filter yet, but I would assume install it in the back area, then just remove my filter element in the front?
My concern is the load on the factory lift pump pushing through 2 filters, adding in the 2-micron cat unit.
For those with the later units that have the spin-on factory filter with water separator in the back (already 2 filters), there is a delete filter kit for the cartridge unit on the block, and I know the water in the fuel sensor screws in the bottom of the factory rear spin on.
So, I have not installed mine, but it appears it will be a 30-minute job if I take my time.
I got it from these guys, I got the single kit for the 2010.
This kit, but they have the 2 filters set up too.
2010 Dodge 2500 SLT CCLB 4WD G56 Cummins 6.7 turbo diesel, 3.42 LSD. Add ons: Banks Monster Ram, Grid heater delete, Spyntec Free Spin Kit with Warn hubs (62672) Laramie Alloys (includes spare), "Powerwagon" Flares, Powerwagon bed decal (4X4 off road) OE Ram mudflaps, OE Slush Mats, OE Clearance Lamps, Geno's shift knob in black, 5" DPF back with muffler delete, spray in bedliner, OE brake controller, Durafit Seat Covers, Pro Tech Toolbox, Speed Turtle, Upfitter switches, Ham Radios, 8 Antennas, headache rack, emergency light bar,....
Just curious, does your “2 Beer” version also have aluminum threads on the head?
2014 RAM 3500 (Aisin) 3.73 4X4 Limited Crew Cab Long Bed DRW. Oil Bypass Filter, Fuel Filtration Kit, Cold Air Intake, City Diesel Actuator and 50 Gallon Aux Fuel Tank.
I will take a peek and see if my two beers have the AL threads or not.
You mentioned a while back a screw in conversion one for metal.
2010 Dodge 2500 SLT CCLB 4WD G56 Cummins 6.7 turbo diesel, 3.42 LSD. Add ons: Banks Monster Ram, Grid heater delete, Spyntec Free Spin Kit with Warn hubs (62672) Laramie Alloys (includes spare), "Powerwagon" Flares, Powerwagon bed decal (4X4 off road) OE Ram mudflaps, OE Slush Mats, OE Clearance Lamps, Geno's shift knob in black, 5" DPF back with muffler delete, spray in bedliner, OE brake controller, Durafit Seat Covers, Pro Tech Toolbox, Speed Turtle, Upfitter switches, Ham Radios, 8 Antennas, headache rack, emergency light bar,....
I think this would suit my needs.
I'll call them today and find out what material they are made from.
I am the upper end of lower class.
I don’t know if they are on here or not, but many are on Google search.
BMP is one (Black Market Performance).
2021 Ram 3500 DRW, H.O., bypass oil filtration, bypass coolant filtration, S&B CAI, 4:10’s
2wd low loc kit.
Reacquired 2001 3500, 5.9 nv4500, dually cab and chassis, 5” straight pipe, edge juice w/attitude. Otherwise all stock…..for now.
Deleted due to I'm a Bone Head!
2017 Bighorn (Delmonico Red & Chrome) CC-HD2500-4WD-6.7L-3:42w/Anti-Spin
Oil: -SHELL- Rotella T6 5W-40 & T5 15W-40 combo w/LF16035
68RFE/BW44-46/Power Steering: -Red Line- C+ ATF
Frontend & Rearend: -Red Line- SAE GL-5 75W-90NS
Many Small Mods: Interior & Exterior
Mileage: 28,541
Bookmarks