Typically when you are turning high RPM often or 50+PSI regularly.
The 366sxe will be in the 50psi range at full tilt. I make 46psi with my 364sxe (stock fuel).
Typically when you are turning high RPM often or 50+PSI regularly.
The 366sxe will be in the 50psi range at full tilt. I make 46psi with my 364sxe (stock fuel).
2013 Ram 2500
John 3:16 - Philippians 4:13
See what we are up to on:
FACEBOOK | INSTAGRAM
Or Email me at:
mike@ddpmotorsports.com
www.ddpmotorsports.com
I was tired and didn’t read the previous post correctly.
My apologies I was doing research and half shared what I’m learning it was late.
The 650 made me think about the setup I’m looking at.
What I believe I found was a 3G swap with 10mm CP3 I’d be topping out at 650. \
I never said a CP3 would give you 100hp.
I’m new to this diesel stuff and trying to learn, I know nothing.
Just sharing what someone with experience shared with me.
Sent from my iPhone using Tapatalk
Ironing out a couple of different build lists.
Will a stock CP3 support the 15% overs I have?
On max effort tune with long duration?
I could be the wrong buck, and I believe a healthy stock CP3 will do just fine for 15% over.
But unsure if you'll lag the fuel on top of the max tune.
However, if your tuned, I'm assuming you already have the injectors in the equation?
Or if the thought is just a general list, then who does the tune can pull or adjust for your current setup.
Don't quote me; someone else will.
Chime in on this, I'm sure.
II 60HP STICKS, II 33% CP3, II S464 2ND GEN SWAP, FASS 165 TITANIUM SIGNATURE SERIES, AFE INTAKE HORN, S&B FILTER, 5" TURBO BACK, ALPHAREX HEAD LIGHTS, 38X13.5X20 RAZOR M/T, MOTO METAL RIMS, 6" LA LIFT KIT, COMPLET MM3 KIT, BUILT TRANSMISSION, 6 BOLT REDHEAD STEERING BOX
Well, pulled the trigger on everything (for now)
today...
the build including what I have already will be:
-drd tunes
-ddp 15% over injectors
-s&b intake
-arp 2000 head studs
-airdog 165 w/ beans sump kit
-GDP horn, grid heater delete and relocate
-Iron horn s366sxe/80/1.0
-hamilton 103# springs and pushrods
-fleece coolant bypass
-egt probe
-fleece fuel filter delete
I dont think i really left any holes in the supporting mods, except a tranny obviously. eventually id like swap out the s&b and get rid of the active air altogether along with doing the intercooler piping. This is already going to be a real handful for me to install myself.
its unclear to me if ill need a riser delete to work in conjunction with the bypass, it appears fleece has discontinued it.
ETA: While i have the injectors out for valve springs i may send them off to get 90hp nozzles put on. eventually upgrade to a 10mm stroker CP3 in conjunction
It sounds like your completely Set.
I want to know the story on how this goes if you don't mind.
Your truck is about to wake the heck up man LOL.
I went with INDUSTRIAL. INJECTION for the price, location, warranty for my 10mm an injectors
When i go twins ill jump up a bit on new injectors, revmax 700\850 is taking priority.
If your married i strongly suggest some spa treatment for a lady's night out after blowing that bill.
II 60HP STICKS, II 33% CP3, II S464 2ND GEN SWAP, FASS 165 TITANIUM SIGNATURE SERIES, AFE INTAKE HORN, S&B FILTER, 5" TURBO BACK, ALPHAREX HEAD LIGHTS, 38X13.5X20 RAZOR M/T, MOTO METAL RIMS, 6" LA LIFT KIT, COMPLET MM3 KIT, BUILT TRANSMISSION, 6 BOLT REDHEAD STEERING BOX
Sure thing man, its going to take a little bit for me to get going on it but ill keep yall updated and I know I'll have questions on the way!
Haha, not married so the only person this hurts is myself.
Things are starting to trickle in.
I also decided to order a DDP 10mm stroker, DDP 90hp nozzles, and the WC fab intake.
Update: I finished putting in the Airdog 165, Beans sump, and Fleece fuel filter delete today.
It started up just fine.
I'm going to put in a few more gallons of diesel to ensure the seal around the sump is holding before I fill it up.
Tomorrow im going to get going on the CP3, head studs, valve springs, push rods, injector nozzles, grid heater delete, new intake horn, new valve cover.
Once all that's wrapped up onto the iron horn kit, coolant bypass, new intake.
You have a full day ahead of you and several curse words LOL.
I wish you the best of luck.
Also, don't hesitate to ask for help when or if you get stumped; that's why we are all here for brother.
Thank you for the update.
II 60HP STICKS, II 33% CP3, II S464 2ND GEN SWAP, FASS 165 TITANIUM SIGNATURE SERIES, AFE INTAKE HORN, S&B FILTER, 5" TURBO BACK, ALPHAREX HEAD LIGHTS, 38X13.5X20 RAZOR M/T, MOTO METAL RIMS, 6" LA LIFT KIT, COMPLET MM3 KIT, BUILT TRANSMISSION, 6 BOLT REDHEAD STEERING BOX
Bookmarks