Thanks Thanks:  8
Likes Likes:  20
Results 1 to 6 of 6

Thread: Dual CP3 Detailed Instructions With Fleece Distribution Block

  1. Top Of Page | #1

    Exclamation Dual CP3 Detailed Instructions With Fleece Distribution Block

    I just installed my Industrial Injection Dual CP3 Kit with Fleece Deluxe Distribution Block.

    The results are amazing!

    This is a must-install for guys looking to get the most power out of their 6.7L Cummins.

    Watch the video and subscribe and hit the like button if you like my video!

    Thanks, Guys.




  2. Thanks watersupply189, IGOTACUMMINS, SyN thanked for this post
    Likes watersupply189, AK Bob, IGOTACUMMINS, SyN liked this post
  3. Top Of Page | #2

    Re: Dual CP3 Detailed Instructions With Fleece Distribution Block

    I have to get a new distribution block!

    The Fleece leeks out of the sensor Allen bolts.

    I may try someone else's distribution block because I even put the ultimate grey gasket on the Allen bolts, and one still leaks.


  4. Thanks IGOTACUMMINS thanked for this post
    Likes watersupply189, IGOTACUMMINS, AK Bob liked this post
  5. Top Of Page | #3
    Permanent Vacation Chrisn162001's Avatar

    User Info Menu

    Re: Dual CP3 Detailed Instructions With Fleece Distribution Block

    Quote Originally Posted by TwinnTibbsDiesel View Post
    I have to get a new distribution block!

    The Fleece leeks out of the sensor Allen bolts.

    I may try someone else's distribution block because I even put the ultimate grey gasket on the Allen bolts, and one still leaks.
    I’ve installed quite a few and never had issues with fleece distribution blocks.

    Fleece truly is top quality.

    I wouldn’t use RTV on the plugs; I’d use thread sealer.

    Call them they will either tell you how to fix it or replace it.


    Sent from my iPhone using Tapatalk


  6. Thanks IGOTACUMMINS thanked for this post
    Likes IGOTACUMMINS, AK Bob, watersupply189 liked this post
  7. Top Of Page | #4

    Re: Dual CP3 Detailed Instructions With Fleece Distribution Block

    Quote Originally Posted by Chrisn162001 View Post
    I’ve installed quite a few and never had issues with fleece distribution blocks.

    Fleece truly is top quality.

    I wouldn’t use RTV on the plugs; I’d use thread sealer.

    Call them they will either tell you how to fix it or replace it.


    Sent from my iPhone using Tapatalk
    Thanks.

    I'm going to call them and see what they say because it didn't leak just a little it leaked enough to leave an 8inch in diameter fuel spot on my driveway and in the parking lot at my job.


  8. Thanks IGOTACUMMINS thanked for this post
    Likes AK Bob, watersupply189, IGOTACUMMINS liked this post
  9. Top Of Page | #5

    Re: Dual CP3 Detailed Instructions With Fleece Distribution Block

    Well, the only thing wrong with this dual CP3 kit was the bracket that holds the upper coolant pipe doesn't work because I have a D&J billet valve cover, and the bracket they give doesn't fit, so I ordered some black Billet 2" clamps that should work to hold the upper coolant hose steady.

    My coolant hose is Gloss Black metal, and I don't want to rub a hole in it, so I hope this bracket holds the pipe away from the top CP3 pump. When I install the bracket, I'll take a picture and post it so everyone else can use it for their own project.

    I'm going to use these https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 for the coolant pipe.

    Also going to use these https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 for my lift pump hoses that are hanging a little bit by the fuel tank and down the frame rail to make it look professional


  10. Thanks IGOTACUMMINS thanked for this post
    Likes watersupply189, IGOTACUMMINS, AK Bob liked this post
  11. Top Of Page | #6

    Re: Dual CP3 Detailed Instructions With Fleece Distribution Block

    Thanks, Guys.

    I will post pics of the brackets installed.

    They worked awesomely.

    I also bought a Pusher knock-off intake elbow because it's the only intake that fits with Industrial Injection's dual CP3 kit.

    I will post a video of the installation because you still have to manipulate it a bit to fit with the back of the 2nd CP3, and I want to paint it gloss black with high temp paint, so it will take me 2 days with painting it.

    I bought a Pusher knock-off because I couldn't spend $350 for a Pusher when it's the same as the $85 knock-off.

    My knock-off has perfect welds and has no cracks at all, and the plate is perfectly flat because my Bro works at a machine shop, and he checked it out, and it's perfectly flat and will seal and flows way better than the stock elbow have on it right now.

    Selling my Banks Monster RAM.

    If anyone wants to buy it for 50% off, PM me.


  12. Thanks IGOTACUMMINS thanked for this post

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •