Thanks Thanks:  10
Likes Likes:  24
Results 1 to 9 of 9

Thread: Turbo Feedline Oring

  1. Top Of Page | #1
    Basic Member

    User Info Menu

    Turbo Feedline Oring

    Hello all, been reading here for years; I finally signed up for an account today.

    The o'ring on the turbo side of the turbo feed line has been leaking for a while, and I can't seem to find any info on a replacement o ring.

    Do I need anything special for the heat generated by the turbo, or will a regular oil-resistant o ring work?

    The one I'm referring to is in the groove on the top side (bigger end) of this part.

    https://www.ebay.com/itm/193474823745


  2. Thanks watersupply189, IGOTACUMMINS thanked for this post
    Likes watersupply189, AK Bob, IGOTACUMMINS liked this post
  3. Top Of Page | #2
    MOD watersupply189's Avatar

    User Info Menu

    Re: Turbo Feedline Oring

    Welcome friend!

    Glad to have ya here.

    Someone hopefully will chime in that’s had to do this.


    2016 Ram 3500 CC 4x4, G56

    2016 RAM 3500 4x4 Laramie Crew Cab
    Cummins,G56, Rough Country level, Morimoto LED fog lights, LED headlights, Lund Attitude Steps sprayed with Line-X, DRL's Activated, 35x12.50R18 Falken Wildpeak ATW3, Fuel Vapor Wheels Matte Black w/Dark Tint, A.R.E. Truck cap and swing boxes

  4. Thanks IGOTACUMMINS thanked for this post
    Likes AK Bob, IGOTACUMMINS liked this post
  5. Top Of Page | #3
    I WILL STAND! AK Bob's Avatar

    User Info Menu

    Re: Turbo Feedline Oring

    Welcome!


    2014 RAM 3500 (Aisin) 3.73 4X4 Limited Crew Cab Long Bed DRW. Oil Bypass Filter, Fuel Filtration Kit and 50 Gallon auxiliary fuel tank.

    Sent from my iPad using Tapatalk

    2014 RAM 3500 (Aisin) 3.73 4X4 Limited Crew Cab Long Bed DRW. Oil Bypass Filter, Fuel Filtration Kit, Cold Air Intake, City Diesel Actuator and 50 Gallon Aux Fuel Tank.

  6. Thanks IGOTACUMMINS thanked for this post
    Likes watersupply189, IGOTACUMMINS liked this post
  7. Top Of Page | #4
    Badger2078's Avatar

    User Info Menu

    Re: Turbo Feedline Oring

    I haven't had this problem, but if we think about it, the engine's oil temperature should be the standing temp here.

    If the oil were hotter at this point, the oil would be cooked rather quickly, so the oil-resistant oil ring should handle a max of approx 250F.

    Sent from my SM-G973U using Tapatalk


  8. Thanks IGOTACUMMINS thanked for this post
  9. Top Of Page | #5
    PFH1987's Avatar

    User Info Menu

    Re: Turbo Feedline Oring

    Were you ever able to find the dash number for the O-Rings?

    I require both.

    Sent from my SM-G892U using Tapatalk


  10. Thanks IGOTACUMMINS thanked for this post
    Likes watersupply189, IGOTACUMMINS liked this post
  11. Top Of Page | #6
    I WILL STAND! AK Bob's Avatar

    User Info Menu

    Turbo Feedline Oring

    @Strickk?


    2014 RAM 3500 (Aisin) 3.73 4X4 Limited Crew Cab Long Bed DRW. Oil Bypass Filter, Fuel Filtration Kit and 50 Gallon auxiliary fuel tank.

    Sent from my iPad using Tapatalk

    2014 RAM 3500 (Aisin) 3.73 4X4 Limited Crew Cab Long Bed DRW. Oil Bypass Filter, Fuel Filtration Kit, Cold Air Intake, City Diesel Actuator and 50 Gallon Aux Fuel Tank.

  12. Thanks IGOTACUMMINS thanked for this post
    Likes watersupply189, IGOTACUMMINS liked this post
  13. Top Of Page | #7
    Basic Member

    User Info Menu

    Re: Turbo Feedline Oring

    I was not able to find an answer.

    I ordered the last fitting they had in stock that was listed in the original post.

    I got it a few days after ordering but have yet to put it in.

    I rebuilt the turbo 2 years ago by hand, and the uninstall and installation by myself with no cherry picker to help still haunts me.

    I'm honestly afraid to break the fitting off in the turbo and have to pull it again.

    I say this because.

    It's not an o-ring that's seated in that fitting.

    It is more of a flat rubber washer that is attached to that fitting.

    It does not come out.


  14. Thanks IGOTACUMMINS thanked for this post
    Likes watersupply189, AK Bob, IGOTACUMMINS liked this post
  15. Top Of Page | #8
    PFH1987's Avatar

    User Info Menu

    Re: Turbo Feedline Oring

    I replaced it with a 2.5mm x 11mm o-ring Buna-N.

    I'll let you know if it leaks and the other o-ring on the bottom looks like a 2.5mm x 12mm.

    I did not replace that one.

    When I took off the hose, I snapped the aluminum supply hose off the top.

    Then removed the two fittings which were fused.

    I had to torch the fittings to get them apart.

    The connector in the turbo came out without issue.


  16. Thanks IGOTACUMMINS thanked for this post
    Likes watersupply189, AK Bob, IGOTACUMMINS liked this post
  17. Top Of Page | #9
    Basic Member

    User Info Menu

    Re: Turbo Feedline Oring

    Thanks for the reply.

    I haven't actually replaced the fitting into the turbo yet.

    I'm too worried about it snapping off and having to clean out and rebuild the turbo again.

    The rebuild isn't the issue at all, and it's the getting it in and out by myself that sucks.

    So I've been soaking it in various oils, hoping when I get the ***** to do it, it will come out without issue.


  18. Thanks IGOTACUMMINS thanked for this post
    Likes AK Bob, watersupply189, IGOTACUMMINS liked this post

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •