Thanks Thanks:  14
Likes Likes:  31
Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15

Thread: Loping/Surging At Low RPM/Acceleration

  1. Top Of Page | #11

    Re: Loping/Surging At Low RPM/Acceleration

    Any luck with an answer on this?

    I know it’s been a while.


  2. Thanks IGOTACUMMINS thanked for this post
    Likes AK Bob, IGOTACUMMINS liked this post
  3. Top Of Page | #12
    Bud2723's Avatar

    User Info Menu

    Re: Loping/Surging At Low RPM/Acceleration

    I'm having a similar issue—the 2018 G56 truck.

    In 4th, 5th, and 6th gear, anything past 50% throttle is hesitant/ surges; the truck kind of shakes a bit just because a black market cat fuel filter conversion issue is still there.

    Any ideas?

    Sent from my SM-G998U1 using Tapatalk


  4. Thanks IGOTACUMMINS thanked for this post
    Likes AK Bob, IGOTACUMMINS liked this post
  5. Top Of Page | #13
    kgharrin's Avatar

    User Info Menu

    Re: Loping/Surging At Low RPM/Acceleration

    You need to monitor actual & desired rail pressure and report back.

    It could be your fuel control actuator (FCA) or some other fueling-related issue.

    As others have suggested, your VGT actuator could be another thing to investigate.

    Without details on the rail pressure and VGT position error, it will be difficult to give helpful advice.

    Is it only happening during cold weather?

    All conditions?

    Warm/cold engine?

    2017 RAM 2500 CTD Blue Streak CCSB | 2.5" Leveling Springs, Toyo AT/III 295/70/R18, DRD MM3

  6. Thanks IGOTACUMMINS thanked for this post
    Likes AK Bob, Corkey, IGOTACUMMINS liked this post
  7. Top Of Page | #14
    Watch Dog! Corkey's Avatar

    User Info Menu

    Re: Loping/Surging At Low RPM/Acceleration

    Unplugging the FCA on the CP3 will give you max rail pressure.

    If you're not shimmed or plugged on the rail, you may pop a code, fuel pressure relief activated.

    This indicates that you are above your threshold of which the rail is limited.

    This only dumps the excess fuel back into the tank until the pressure is relieved.

    Unplug FCA, start the truck "with no throttle," check the numbers for actual v desired, and shut the motor off.

    I forget what the deviated number is between the two.

    They should be relatively close to one another.

    You will notice a sound different than usual, as this is giving you max rail pressure at idle.

    If the numbers are pretty close, I will look at the VGT van position as stated above.

    If those are in good standing, I'm curious if, depending on how many miles are on the CP3, it's going out or not.

    II 60HP STICKS, II 33% CP3, II S464 2ND GEN SWAP, FASS 165 TITANIUM SIGNATURE SERIES, AFE INTAKE HORN, S&B FILTER, 5" TURBO BACK, ALPHAREX HEAD LIGHTS, 38X13.5X20 RAZOR M/T, MOTO METAL RIMS, 6" LA LIFT KIT, COMPLET MM3 KIT, BUILT TRANSMISSION, 6 BOLT REDHEAD STEERING BOX, YUKON 4.56 GEARS W/ COVERS

  8. Thanks IGOTACUMMINS thanked for this post
    Likes AK Bob, IGOTACUMMINS liked this post
  9. Top Of Page | #15
    Watch Dog! Corkey's Avatar

    User Info Menu

    Re: Loping/Surging At Low RPM/Acceleration

    Any new update on the numbers?

    II 60HP STICKS, II 33% CP3, II S464 2ND GEN SWAP, FASS 165 TITANIUM SIGNATURE SERIES, AFE INTAKE HORN, S&B FILTER, 5" TURBO BACK, ALPHAREX HEAD LIGHTS, 38X13.5X20 RAZOR M/T, MOTO METAL RIMS, 6" LA LIFT KIT, COMPLET MM3 KIT, BUILT TRANSMISSION, 6 BOLT REDHEAD STEERING BOX, YUKON 4.56 GEARS W/ COVERS

  10. Thanks IGOTACUMMINS thanked for this post
    Likes AK Bob, IGOTACUMMINS liked this post
Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •