Thanks Thanks:  2
Likes Likes:  13
Results 1 to 7 of 7

Thread: Using Edge 98004 Adatper with Triple Gauge Pod?

  1. Top Of Page | #1

    Using Edge 98004 Adatper with Triple Gauge Pod?

    Not sure if this is in the right section or not, but has anyone used the edge 98004 adapter to mount an MM3 on one of the Autometer triple gauge pillar pods.

    I was thinking about buying the preloaded setup that come with tranny temp, pyromoter, and boost gauges, and changing the tranny temp out for the MM3 if it will fit, and mount the tranny temp in a single gauge pod for the steering column.

    2016 Ram 5500 6.7cummins 4x4 G56 11ft Knapheide service bed
    Kenwood x893s with infinity kappa 3 way components and 2 JL w3 12s
    Ranchhand legend bullnose front bumper
    The Ram Man Inc unlocking hubs - 285/70/19.5s on AWM wheels
    to do list - Valair quiet street dual disk clutch - 2.5" lift kit - DRD MM3 with deletes.
    - switch stereo to active crossovers and add another phoenix gold amp.

  2. Likes watersupply189, timshooter40 liked this post
  3. Top Of Page | #2
    Basic Member JSteadly's Avatar

    User Info Menu

    Re: Using Edge 98004 Adatper with Triple Gauge Pod?

    Ordering the adapter this week and doing this exact set up.

    How did it work out?


  4. Likes watersupply189, timshooter40 liked this post
  5. Top Of Page | #3
    timshooter40's Avatar

    User Info Menu

    Re: Using Edge 98004 Adatper with Triple Gauge Pod?

    I would love to see pics of how it looks when you are done with the install.

    2016 Ram 2500 CCSB 4X4 ,Cat fuel filter delete with water seperator. Thuren suspension
    with Fox IFP shocks, thuren sway bar, rear track bar and front track bar, Warn 12k winch , custom winch mount, REVMAX trans pan,HD valve body and thermal bypas. Leer truck topper,Exotic head studs, Engine enhancements by the cummins whisper.

  6. Likes AK Bob, watersupply189 liked this post
  7. Top Of Page | #4
    Basic Member Cweaver's Avatar

    User Info Menu

    Re: Using Edge 98004 Adatper with Triple Gauge Pod?

    Quote Originally Posted by timshooter40 View Post
    I would love to see pics of how it looks when you are done with the install.
    I have a similar setup if this helps.




    Sent from my iPhone using Tapatalk


  8. Thanks timshooter40, IGOTACUMMINS thanked for this post
  9. Top Of Page | #5
    ReggieK's Avatar

    User Info Menu

    Re: Using Edge 98004 Adatper with Triple Gauge Pod?

    Cweaver - which triple pod is that? Do you have it on a 2016 truck? I have a 2017 and was looking at autometer's triple pod...and even talked to them and they said their pod was not a direct replacement and had to be screwed over top of the factory a pillar. I have grab handles on my truck so they would need to be cut off...yours looks like a direct replacement and is what I'm looking for...and I don't think there's any changes to the interior from 2016 to 2017. If you could point me in the right direction to get that pod it would be appreciated.


  10. Likes watersupply189 liked this post
  11. Top Of Page | #6
    ReggieK's Avatar

    User Info Menu

    Re: Using Edge 98004 Adatper with Triple Gauge Pod?

    Quote Originally Posted by ReggieK View Post
    Cweaver - which triple pod is that? Do you have it on a 2016 truck? I have a 2017 and was looking at autometer's triple pod...and even talked to them and they said their pod was not a direct replacement and had to be screwed over top of the factory a pillar. I have grab handles on my truck so they would need to be cut off...yours looks like a direct replacement and is what I'm looking for...and I don't think there's any changes to the interior from 2016 to 2017. If you could point me in the right direction to get that pod it would be appreciated.
    Quote Originally Posted by Cweaver View Post
    I have a similar setup if this helps.

    https://uploads.tapatalk-cdn.com/201...1c4aa3ce28.jpg


    Sent from my iPhone using Tapatalk
    Sorry...same question twice...wasn’t sure if you’d see it without being quoted


  12. Top Of Page | #7
    Basic Member Cweaver's Avatar

    User Info Menu

    Re: Using Edge 98004 Adatper with Triple Gauge Pod?

    Quote Originally Posted by ReggieK View Post
    Sorry...same question twice...wasn’t sure if you’d see it without being quoted
    I’m not sure I bought it off here used I think he said it was a autometer.

    It was a pain to get it in between the dash but after you figure it out it slides right in.


    Sent from my iPhone using Tapatalk


  13. Likes watersupply189 liked this post

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •