Thanks Thanks:  4
Likes Likes:  5
Results 1 to 5 of 5

Thread: How to turn up your P-Pump

  1. Top Of Page | #1
    Inactive Vendor

    User Info Menu

    How to turn up your P-Pump

    Seeing as there are lots of people here new to the diesel world here is a How-to from my computer for turning up your P-Pump found on 94-98 dodge cummins trucks

    The steps for turning up a P7100 pump are:

    1) Remove your AFC Housing
    2) Mod Your Fuel Plate either slide it forward or purchase a cut one
    3) Adjust the governor lever to contact the fuel plate
    4) Crank the star Wheel Towards the motor
    5) Slide The AFC housing all the way forward

    Details Below……




    AFC Removal





    If you do almost any pump work you have to take the AFC housing off.
    Remove front passenger side AFC
    housing break off screw.
    NOTE: This screw is a factory break off screw with rounded head and no screw driver, allen head or TORX slot.

    Use a hand impact tool with a 6 inch long 1/4″ extension and a T15 TORX bit to remove this screw.
    A center punch may be required to start a hole in the center of this screw.
    Set the hand impact tool in the removal position (counter clockwise) and use light hammer taps on the impact tool to loosen this screw.
    Tap progressively harder on the impact tool until the screw loosens.
    This method of removal forms a TORX shape into the screw allowing it to be reinstalled later with the T15 TORX bit.
    In some cases the hole in the top of this screw is too large for the T15 bit thus use the T20 TORX bit.
    There is usually a lock washer and flat washer under each of these screws.

    OPTIONAL: A sharp chisel can be used to remove the break off screw by making a notch in the outside diameter of the head, then applying a tangential force with light blows to the chisel counterclockwise to remove the screw.




    AFC Cut Away



    Fuel Plate




    With the AFC housing removed you can now see the fuel plate .
    Sliding the stock plate will increase HP quite a bit.
    Slide the plate ATW Foward and if you still want more contact me for a Cut Plate, or PM me, send me yours and for a small fee i will cut it to whatever profile you would like





    This is what it looks like under the fuel plate
    Governor Lever Adjustment




    This is a cut away view of the governor of a P7100 pump. Notice how the lever hit the cam plate flush at the very bottom edge. To check your adjustment the throttle lever needs to be moved until the lever just touches the cam plate. With the AFC housing removed, look down through the opening behind the cam plate and see where the lever is striking the plate. This should be done with the Fuel Shutoff Solenoid in the run ( or pulled up ) position.
    Where the lever strikes the cam plate will vary depending on the style and design of the cam plate you are using. For plates similar to the stock plate, like shown below, this lever is set correctly. It is adjusted so the lever is flush with the bottom edge of the plate, and does not ride under the plate.
    (Picture Courtesy of BD Power)



    For cam plates, that have a taper at the very bottom of the plate, adjust the lever so the lever hits at the tip of the bottom nose on the plate. It is OK to be slightly below that. However too far down causes the lever to be held back as the RPM’s rise. This causes the loss in bottom end power, with the sudden surge as the lever finally clears the nose and hits the main fueling curve.





    This is what the pump looks like from the back with the cover removed. Do not change the adjustment in the upper right hand corner. The adjustment in the lower left hand corner is the one to make. Loosen the locknut ( 10mm socket required ). Making very small adjustments to the screw, adjust the lever the proper height. Now tighten the locknut.
    One thing to realize about the plate is that it is properly called a full load throttle stop. What this means is that if you are not running at WOT or close to it the plate is not doing anything. It’s just taking up space in the pump.
    Star Wheel Adjustment




    To adjust, remove the large plug on top of the AFC housing using an 8 mm allen wrench. Take care not to loose the sealing washer under the plug. Removing the plug exposes a star wheel which changes the quickness of fueling response to boost. If acceleration is weak with minimal smoke, rotate top of the star wheel toward the engine a few revolutions. If vehicle has heavy black smoke on initial acceleration, rotate top of star wheel away from engine a few revolutions. Reinstall large plug with sealing washer and test drive vehicle again. It may take repeated attempts to get this adjustment set. If heavy smoke is still encountered with star wheel moved completely to rear position, loosen AFC housing and slide it rearward a 1/16 inch, retighten and test again. Repeat unit desired results occur.








  2. Top Of Page | #2
    WE WILL STAND! IGOTACUMMINS's Avatar

    User Info Menu

    Great info!

    "The grass is greener where you water it"


  3. Top Of Page | #3
    Inactive Vendor

    User Info Menu

    Make that a sticky for me jj


  4. Top Of Page | #4
    Old & Grumpy! Polaraco's Avatar

    User Info Menu

    This thread got stuck. LOL Made it sticky


    2003- 3500 RWD Automatic.
    S & B intake, BD Intercooler, Pusher Air Horn, MM3 Double R Tuning, Turbo Timer, electric Flex-a-lite fans, FASS 95,
    50 HP tips, upgrade to 351 turbo, 3.42 gears, Twin air compressors, air bags, Remote dual oil filters, Hellwig sway bar, Front Winch. Home made Fuel Heater, BD Exhaust brake with Torque Lock. Tons of TLC

  5. Likes IGOTACUMMINS liked this post
  6. Top Of Page | #5
    Basic Member

    User Info Menu

    Fuel plate? What fuel plate???


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •