Thanks Thanks:  18
Likes Likes:  49
Page 3 of 3 FirstFirst 123
Results 21 to 29 of 29

Thread: EGT SENSOR INSTALL W/EGR COOLER IN PLACE.

  1. Top Of Page | #21
    z28-50's Avatar

    User Info Menu

    Re: EGT SENSOR INSTALL W/EGR COOLER IN PLACE.

    Are you guys adding EGT probes to both the down pipe and exhaust manifold?

    Is this the MM3 EGT probe or something else?

    2015 / RAM / 2500 CTD-68RFE-4wd / 3.42 / stock tire size / Silver / Bighorn

  2. Top Of Page | #22
    Permanent Vacation Chrisn162001's Avatar

    User Info Menu

    Re: EGT SENSOR INSTALL W/EGR COOLER IN PLACE.

    Post turbo temp is going to be a lot cooler than pre turbo temp.


    Sent from my iPhone using Tapatalk


  3. Likes AK Bob, timshooter40 liked this post
  4. Top Of Page | #23
    z28-50's Avatar

    User Info Menu

    Re: EGT SENSOR INSTALL W/EGR COOLER IN PLACE.

    Quote Originally Posted by Chrisn162001 View Post
    Post turbo temp is going to be a lot cooler than pre turbo temp.


    Sent from my iPhone using Tapatalk
    Agreed, but I know my baselines today as I monitor 4 exhaust temperature sensors.

    The one I watch closest is #1 in the downpipe.

    I never turn the truck off until this under 400* F.

    Side note; the next 2 sensors (#2and #3) get very hot during Regen., up to 1800*F.

    I wonder if the MM3 can monitor exhaust temp sensor #1.

    2015 / RAM / 2500 CTD-68RFE-4wd / 3.42 / stock tire size / Silver / Bighorn

  5. Top Of Page | #24
    Permanent Vacation Chrisn162001's Avatar

    User Info Menu

    Re: EGT SENSOR INSTALL W/EGR COOLER IN PLACE.

    Quote Originally Posted by z28-50 View Post
    Agreed, but I know my baselines today as I monitor 4 exhaust temperature sensors.
    The one I watch closest is #1 in the down pipe.
    I never turn the truck off until this under 400* F.
    Side note; the next 2 sensors (#2and #3) get very hot during Regen., up to 1800*F.

    I wonder if the MM3 can monitor exhaust temp sensor #1 .
    Number 1 as in DPF inlet? Or your down pipe sensor?

    Are you factory or maxing out a emissions intact tune.

    I’m not grasping why you want to monitor egts so closely.

    I’ll go from a 1600 degree egts from a wot pull to idle and mine drops down below 400 degrees in a matter of seconds.


    Sent from my iPhone using Tapatalk


  6. Likes AK Bob, timshooter40 liked this post
  7. Top Of Page | #25
    z28-50's Avatar

    User Info Menu

    Re: EGT SENSOR INSTALL W/EGR COOLER IN PLACE.

    Quote Originally Posted by Chrisn162001 View Post
    Number 1 as in DPF inlet? Or your down pipe sensor?

    Are you factory or maxing out a emissions intact tune.

    I’m not grasping why you want to monitor egts so closely.

    I’ll go from a 1600 degree egts from a wot pull to idle and mine drops down below 400 degrees in a matter of seconds.


    Sent from my iPhone using Tapatalk
    I am factory at this point.
    I believe number 1 is in the downpipe - post turbo temp..
    I let if cool off to below 400 so as to not "coke" oil in the turbo bearings. (maybe ****)

    The others I started off monitoring to learn what it was doing during a Regen.

    If driving around town it takes about 1 minute to drop to 400 or below.

    If coming off the freeway after towing my trailer it takes about 3 minutes to drop to 400.

    2015 / RAM / 2500 CTD-68RFE-4wd / 3.42 / stock tire size / Silver / Bighorn

  8. Likes AK Bob, timshooter40 liked this post
  9. Top Of Page | #26
    Permanent Vacation Chrisn162001's Avatar

    User Info Menu

    Re: EGT SENSOR INSTALL W/EGR COOLER IN PLACE.

    Quote Originally Posted by z28-50 View Post
    I am factory at this point.
    I believe number 1 is in the downpipe - post turbo temp..
    I let if cool off to below 400 so as to not "coke" oil in the turbo bearings. (maybe ****)

    The others I started off monitoring to learn what it was doing during a Regen.

    If driving around town it takes about 1 minute to drop to 400 or below.

    If coming off the freeway after towing my trailer it takes about 3 minutes to drop to 400.
    Exhaust temp sensor 1 is gonna be labeled DPF inlet or pre DPF temp sensor or something along those lines it’s located at the end of the down pipe where it bolts to the DPF.

    The sensor post turbo on the elbow is a nox sensor, not sure if that’s the one you are referring too.


    Sent from my iPhone using Tapatalk


  10. Likes AK Bob, timshooter40 liked this post
  11. Top Of Page | #27
    I WILL STAND! AK Bob's Avatar

    User Info Menu

    Re: EGT SENSOR INSTALL W/EGR COOLER IN PLACE.

    Quote Originally Posted by JasonV123 View Post
    Can you tell me what size tap you used to fit the probe threads?

    Thanks
    The probe adapter fitting should be 1/8” NPT 27 TPI.


    2014 RAM 3500 (Aisin) 3.73 4X4 Limited Crew Cab Long Bed DRW. Oil Bypass Filter, Fuel Filtration Kit and 50 Gallon auxiliary fuel tank.

    Sent from my iPad using Tapatalk

    2014 RAM 3500 (Aisin) 3.73 4X4 Limited Crew Cab Long Bed DRW. Oil Bypass Filter, Fuel Filtration Kit, Cold Air Intake, City Diesel Actuator and 50 Gallon Aux Fuel Tank.

  12. Likes timshooter40 liked this post
  13. Top Of Page | #28
    JasonV123's Avatar

    User Info Menu

    Re: EGT SENSOR INSTALL W/EGR COOLER IN PLACE.

    Quote Originally Posted by AK Bob View Post
    The probe adapter fitting should be 1/8” NPT 27 TPI.


    2014 RAM 3500 (Aisin) 3.73 4X4 Limited Crew Cab Long Bed DRW. Oil Bypass Filter, Fuel Filtration Kit and 50 Gallon auxiliary fuel tank.

    Sent from my iPad using Tapatalk
    Thanks!!


  14. Thanks IGOTACUMMINS thanked for this post
    Likes AK Bob, timshooter40, IGOTACUMMINS liked this post
  15. Top Of Page | #29
    Booch035's Avatar

    User Info Menu

    Re: EGT SENSOR INSTALL W/EGR COOLER IN PLACE.

    Has anyone drilled and tapped their 5th Gen manifold?

    I am trying to figure out if removing the wheel well liner will give enough access to drive it.

    2021 2500 68RFE..... I'll just keep the goodies a secret!!!

  16. Thanks IGOTACUMMINS thanked for this post
    Likes IGOTACUMMINS, AK Bob liked this post
Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •