MM3 Power

Thanks Thanks:  1
Likes Likes:  4
Results 1 to 10 of 10

Thread: 2013 dodge 4500

  1. Top Of Page | #1
    Basic Member DOTOJ's Avatar

    User Info Menu

    2013 dodge 4500

    Hi!! Im new to the forum, have a question. I don't have a lot of resources where I work, I have a p2400 code on a 13 dodge 4500. Ideas on where to start or common issues? Thanks!!


  2. Likes AnOldBiker liked this post
  3. Top Of Page | #2
    Old ... But Still Here ! AnOldBiker's Avatar

    User Info Menu

    Re: 2013 dodge 4500

    @DOTOJ


    Does anyone have the webpage with all the P codes handy ? I can't find mine.



    Jim


    2006 ~ 2500HD, Big Horn Edition, 5.9, 4x4, Q/Cab, 48RE, L/B, 3.73, S&B CAI & Snout, ProFlo 5" S/S exhaust, Smarty Touch, Oil ByPass Kit, 60 gal main tank, 110 gallon in-bed tank, XX-Fuel System, Coolant Bypass Kit, Mag-Hytec front & rear end covers and trans pan, 285 x 70 x 17

    "Freedom is never more than one generation away from extinction. We didn't pass it to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same, or one day we will spend our sunset years telling our children and our children’s children what it was once like in the United States, where men 'were' free." ~ Ronald Regan

  4. Top Of Page | #3
    Basic Member DOTOJ's Avatar

    User Info Menu

    Re: 2013 dodge 4500

    I found the code...P2400

    EVAP Leak Detection Pump Ctrl Circ/Open

    has anyone dealt with this? I don't usually get these smaller trucks, emissions are quite different from a Mack.
    Thanks!!


  5. Top Of Page | #4
    Basic Member DOTOJ's Avatar

    User Info Menu

    Re: 2013 dodge 4500

    Also!!! has fuel service required on dash message center.... related??


  6. Top Of Page | #5
    Senior Member F350Cummins's Avatar

    User Info Menu

    Re: 2013 dodge 4500

    Change fuel filters, clear the code run it awhile and rescan for codes. I seem to think the P2400 will come from another code.

    But on another note, what is done to the truck? I seem to think this could stem from a sensor to the EGR DPF DEF system, or SCR. Not sure where the HD goes with the SCR vs EGR/dpf

    2016 Tradesman 2500 picked up 9/28/16 MM3 with Rays Emission compliant EGR-Less Tuning and 12V tune

    Future plans: Fass, head studs,

    Other Toys: 1973 Charger Bougham edition 400 big block 42K original miles Unicycles (about 3 dozen)


    6 in a row makes her go

  7. Top Of Page | #6
    Basic Member DOTOJ's Avatar

    User Info Menu

    Re: 2013 dodge 4500

    That is the only code. The only other thing is the service fuel system on lcd message center. The crankcase breather had never been changed and was blowing oil out onto the valve cover, I changed that.


  8. Top Of Page | #7
    Senior Member F350Cummins's Avatar

    User Info Menu

    Re: 2013 dodge 4500

    any tuning or other mods?

    2016 Tradesman 2500 picked up 9/28/16 MM3 with Rays Emission compliant EGR-Less Tuning and 12V tune

    Future plans: Fass, head studs,

    Other Toys: 1973 Charger Bougham edition 400 big block 42K original miles Unicycles (about 3 dozen)


    6 in a row makes her go

  9. Top Of Page | #8
    Basic Member DOTOJ's Avatar

    User Info Menu

    Re: 2013 dodge 4500

    no mods, state owned truck


  10. Top Of Page | #9
    Basic Member DOTOJ's Avatar

    User Info Menu

    Re: 2013 dodge 4500

    update... I got my hands on a decent scan tool. p2400 was not in there as it shouldn't be. P2400 is an evap code for a gas engine. The code that was in there was P2509. ecm power issue. oddly after some research this code is also related to a bad fan clutch. I believe the problem came from an ignition key/ lights being left on over night.


  11. Likes Power247 liked this post
  12. Top Of Page | #10
    Basic Member DOTOJ's Avatar

    User Info Menu

    Re: 2013 dodge 4500

    another update. After a coupole of test drives another code came up P24ED. Its an ammonia sensor. I checked with the dealer and this truck has open recalled for aftertreatment and shift lock. Off to the dealer it goes


  13. Thanks IGOTACUMMINS thanked for this post
    Likes IGOTACUMMINS, Power247 liked this post

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •