Re: Intake Horn Banks A "Hole"
Does the intake horns from an 18 work on the 19 or 20?
Looking at buying 2020, of course, they did make an intake horn for them yet.
Re: Intake Horn Banks A "Hole"
Quote:
Originally Posted by
flanagan
I don't know.
I haven't installed it yet still snowing in Colorado.
I'll let you know after I install it.
Sent from my SM-G973U using Tapatalk
You did a good job!
I have the Banks and Love it. :)
Re: Intake Horn Banks A "Hole"
Quote:
Originally Posted by
TwinnTibbsDiesel
You did a good job!
I have the Banks and Love it. :)
I posted somewhere on another post here after working 13 Hours 17 below.
The truck sitting outside is not plugged in.
I went to remote start the truck, and the batteries were dead got a jump from my buddy.
The truck started right up, stumbled for a few seconds, and smoked for a few minutes, but the heater did keep the truck running well.
Sent from my SM-G973U using Tapatalk
Re: Intake Horn Banks A "Hole"
I feel you; it was just freezing a couple of weeks ago in Michigan, and I would start my Dually up, and it would chug a little, but it always started and smoothed out after 2-3 minutes too.
Quote:
Originally Posted by
flanagan
I posted somewhere on another post here after working 13 Hours 17 below.
The truck sitting outside is not plugged in.
I went to remote start the truck, and the batteries were dead got a jump from my buddy.
The truck started right up, stumbled for a few seconds, and smoked for a few minutes, but the heater did keep the truck running well.
Sent from my SM-G973U using Tapatalk
Re: Intake Horn Banks A "Hole"
Thx for the pictures, I am thinking of doing the same.
What size drill and tap did you use?
Re: Intake Horn Banks A "Hole"
Quote:
Originally Posted by
Skiwhat
Does the intake horns from an 18 work on the 19 or 20?
Looking at buying 2020, of course, they did make an intake horn for them yet.
Yes, it does, I bought the RAM horn from the guys at DDP, and everything fits up the same.
The only difference is the 1# fuel line but everything bolts.
Re: Intake Horn Banks A "Hole"
Quote:
Originally Posted by
Roberto Fisherman
Thx for the pictures, I am thinking of doing the same.
What size drill and tap did you use?
Does anyone know the answer?
What size drill and tap?
Sent from my iPhone using Tapatalk
2 Attachment(s)
Re: Intake Horn Banks A "Hole"
Quote:
Originally Posted by
flanagan
Drilled?
That is where it is supposed to go (heater) and doubles as an access hole to get the middle horn bolt in.
Use Loctite blue on all your horn bolts.
You will need to replace your #1 injector line too.
Attachment 15558
Attachment 15559
Re: Intake Horn Banks A "Hole"
Quote:
Originally Posted by
toyota_mdt_tech
Drilled?
That is where it is supposed to go (heater) and doubles as an access hole to get the middle horn bolt in.
Use Loctite blue on all your horn bolts.
You will need to replace your
#1 injector line too.
Attachment 15558
Attachment 15559
Unfortunately, the older Banks intake horns were not pre-drilled and taped for the screw-in grid heaters.
Re: Intake Horn Banks A "Hole"
Quote:
Originally Posted by
SpryGuy
Does anyone know the answer?
What size drill and tap?
Sent from my iPhone using Tapatalk
22mm X 1.5 thread pitch.
Standard Motor Products' part number is DIH4 for the heater element.
https://m.media-amazon.com/images/I/...AC_SL1500_.jpg